Whirlpool Electric Dryer

If your Whirlpool electric dryer has stopped heating, it can wreak havoc on your life until it’s repaired. If you’re a bit handy, this article will help you locate the most common components that can fail and cause the dryer to stop heating.

When working on an electric dryer, the first thing to be aware of is that it plugs into a 240 volt outlet. It’s very important to make sure that the dryer in unplugged before attempting any diagnostics with the dryer.

There are several components in a dryer that can fail and cause it not to dry. Using a multi-meter, these components can easily be checked from accessing them at the rear of the dryer whirlpool dryer repair pasadena.

First, make sure the dryer cord has been removed from the outlet. Next detach the vent from the rear of the dryer and move it to the side. You will have to remove ten 1/4 sockets screws to remove the back panel. From here you can check the heating element, thermal fuse, hi-limit thermostats and operating thermostat.

The heater is located on the right side. To check the heating element, remove the two red wires attached to the heater terminal located on bottom of the heater casing. Test the terminals with your multi-meter and you should have continuity. If not, then the heating element is faulty and will need to be replaced.

Another component that fails often is the thermal fuse which is located on the left side. The thermal fuse is white, thin and about two inches in length. Check this for continuity. If the fuse is bad, you will want to make sure that the dryer venting leading from the dryer to outside is clear. If it gets too hot inside the dryer, this non reset able fuse will fail.

Attached to the heating element casing are two hi-limit thermostats that can be tested for continuity. Unplug the wires and test with your multi-meter. One thermostat is located on the top and the other on the bottom near the heating element terminals. If these thermostats fail, they will cut power to the heating element.

Finally, from the rear of the dryer, the operating thermostat can be tested. The operating thermostat cycles the heat to turn on and off in order to maintain an average temperature near 155 degrees on the normal cycle. It’s located just below the thermal fuse. Check the continuity between the two larger terminals on the thermostat. If the it does not have continuity, it will have to be replaced.

If after testing these components the dryer is still not heating, you may have to call your local appliance repair company to investigate further. The problem may lie with a few more components or wiring.

Make It Start with a Door Switch – Dishwasher Repair

You wouldn’t even know your dishwasher had one until it isn’t working. These little switches are tucked inside the control panel of your dishwasher and most times are a part of the door latch. The door latch pulls the door securely to the main body of your dishwasher and prevents water from leaking during a cycle. If your dishwasher doesn’t start, it could be due to a faulty door switch.

How the door switch works

When the dishwasher door is open, the switch is off. Inside your dishwasher tub will be a metal or plastic prong. Close and latch the door. The prong will depress the door switch completely and the circuit will close allowing the dishwasher to start. Check the prong to make sure it’s not loose or bent and it’s properly activating the door switch ge dishwasher repair pasadena.

It is important to disconnect the dishwasher from its power source before attempting any repair. You can unplug the dishwasher from the outlet, remove the fuse from your fuse box, or flick the breaker switch on your circuit panel. This will prevent you from getting an electric shock.

What a door switch looks like and where it’s located

Typically a dishwasher door switch is an inch long. It can be black or red and has metal prongs called terminals protruding from the body. Some door switches have two terminals and some have three.

The terminals can be a common terminal (COM), normally closed terminal (NC) or a normally open terminal (NO). Switches with only two terminals will either have a COM and a NO, or a COM and an NC. Door switches with three terminals have COM, NC, and a NO.

Your dishwasher’s door switch will be behind the control panel on the front of the unit. It may be necessary to remove the inner panel of the door first. You can do this by removing a few screws. The screws at the bottom of the door are for the hinges. You do not need to remove the whole door for this repair.

Once the inner panel is removed you may find another smaller panel covering the back of the control panel held in place with screws or clips. By removing this panel you will gain access to the latch assembly housing the door switch.

How to remove the switch

Carefully use needle nose pliers to pull the wires leading from the harness off the terminals. For door switches that have a locking clip, depress the lever as you gently pull the harness away from the terminal.

Take your time while removing switches that are a part of the latch assembly or that have a bracket. If you rush and break the switch’s housing you will end up having to replace more parts.

How to test your door switch

Use an ohmmeter to test the switch for continuity. This test is for door switches with three terminals.

Set your ohmmeter to measure resistance at a scale of Rx1.
Touch the metal tips of the test leads together and zero your ohmmeter by adjusting the thumbwheel in the front of the meter until the needles reads “0” on the scale.
Touch one meter lead to the COM terminal and the other lead to the NO terminal. Do not push in on the actuator.
Your meter should give a reading of infinity, meaning the circuit is open, and there is no continuity.
Without moving the meter’s leads, press down on the actuator until you hear a ‘click’.
With the ‘click’ of the actuator, the meter should produce a resistance reading of zero ohms. This means the circuit is closed and continuity is present. (You will only hear this click with a door switch with three terminals.)
Keep the meter lead that is touching the COM terminal in place, but move the other meter lead from the NO terminal to the NC terminal.
When the actuator is released, you should receive a resistance reading of zero ohms.
Now set your ohmmeter to its highest resistance scale and touch one meter lead to the NO terminal and the other meter lead to the NC terminal.
The resistance reading between these two leads should be infinite.
Finally take a resistance reading from both the NC terminal and the NO terminal to any metal mounting hardware that is a part of the switch assembly. You should receive a normal reading of infinity.
Any readings that differ from the tests above are signs of a defective door switch that will need to be replaced.

Should You Repair Your Appliance?

I want the public to know that the new machines out their are not lasting as long as machines that were built 10 to 20 years ago. It does not matter what brand it is: Kenmore, Whirlpool, GE, Maytag you get the idea.

In my opinion the older machines were built like tanks! They have less electronics in them and in my opinion they were built with better parts. Before you buy a new machine keep in mind that almost anything you buy today will have a electronic control board in it and the more gadgets the refrigerator, washer, dryer, dishwasher or oven has the more things that can go wrong with it. If your machine is in good condition and has been well maintained then you should think about repairing your appliance. The cost of the repair in most cases will be far less than a new machine. Also, most new machine’s will not last as long as your parents machine did! And I have just recently discovered that the Appliance manufacture’s have been cutting back on the warranty coverage of refrigerator’s seal systems, some of them use to be over 10 years and now are only one year…. whats that tell ya?

For those of you that I could not convince and your almost out the door to purchase a new appliance I have a couple of Tips for you.

First, do a litter home work, research the appliance your going to buy maytag stove and oven repair pasadena. Do a search online about the appliance you want to buy to see if customers are having a problem with it, and do not just look at review pages find some blogs, get the model number of the appliance your thinking of buying and do a help search on the internet. (Example: help (your model #) washer) and see what comes up on the internet. I personally looked up a LG dishwasher that had 3000 complaints on it. Of course you can not rule out something just because it has a couple of complaints.

Second, when your at the check out ready to pay for your new machine, they are going to want you to purchase a extended warranty on the appliance. If you do not have a home warranty that covers your appliance’s and your spending a lot of money on the machine you should get the warranty. As I said, the new machines can have more than one control board and lighting and power serges can cause problems with these newer machines, and the makers of appliances are not putting serge protectors on them witch is something else you might what to buy for it also.

Third, on the positive side. I can say that I am happy with front load washers, they do save a lot of water, when a front load washer fills it only uses a few gallons of water compared to 10 gallons or more on a top load washer every time it fills. This could save you hundreds of gallons of water a year. The customers I have talked with say it washes very well. On the negative side, the cost of repair could be on the high side, so don’t forget about that extended warranty.

Garments Dryer

There are two kinds of garments dryers one is gasoline the opposite is electrical. The gasoline dryer is half gasoline and half electrical, the gasoline is used for lighting a flame to create the warmth to dry the garments, the electrical is used to function the motor, timer, ignitor, coil package and thermostats.

The gasoline dryer has extra working elements than the electrical dryer, when there are extra working elements there’s a larger likelihood of one thing breaking, the gasoline dryer does break down extra steadily than the electrical dryer.

The electrical dryer use 220 volts to function the heater component solely whirlpool dryer repair los angeles, all the opposite elements use 110volts. Each gasoline and electrical dryer have some primary elements: motor, timer, belt, thermostats, and thermal fuse.
These are the features of every half.

The motor turns the belt that’s on the basket, the timer sends the specified voltage to every half for the specified time that it’s set on, the thermostat maintains the specified temperature and the thermal fuse shuts down the dryer if the thermostat fails.

A typical drawback with each gasoline and electrical is garments taking a really very long time to dry, lint build up within the exhaust vent hose is typically the explanation. The easiest way to verify if the exhaust is partially blocked is to activate the dryer. Then go exterior to the place the vent is, put your hand near the vent, if there’s little or no sizzling air popping out out, your vent hose is blocked. There needs to be a robust move of sizzling air popping out. Generally birds construct their nest on the vent opening due to the nice and cozy air they discover popping out of it. Additionally if the vent comes out close to the bottom it typically get coated by snow.

How you can Know You Want Skilled Dwelling Equipment Repairs

Noticing once you want equipment restore may also help you get monetary savings. By fixing your damaged equipment within the begin, you’ll be able to usually forestall the necessity for pricey alternative equipment.

So paying some consideration on how nicely your private home home equipment are working is certainly a good suggestion if you happen to actually need to just remember to don’t need to find yourself footing vitality payments which might be increased than they’d should be. Maintain a glance out for indicators that you just want equipment restore as a result of it might probably absolutely provide help to make sure you get most worth out of your private home home equipment and can even maintain your pockets protected samsung appliance repair pasadena.

Some Indicators You Want Equipment Repairs

There are fairly a number of apparent indicators that you just want equipment restore in your house. As an illustration, a few of your home equipment might cease working altogether. Your dishwasher might not activate, or your fridge might cease working effectively, then you recognize it’s time to rent an equipment restore firm. Whilst you might imagine that by laying aside your dishwasher restore by washing your dishes with hand it can save you some cash, the reality is that you could be find yourself paying extra to your water payments since most dishwashers are extra environment friendly than hand washing. So it’s apparent that when your dishwasher is damaged, then you should safe skilled equipment restore service instantly. Having your machine up and operating once more can be way more vitality environment friendly and also will minimize down in your water utilization. You additionally received’t should spend hours washing your dishes with hand. You too can save a big quantity on a alternative unit.

Typically the indicators you want equipment restore should not so apparent. Some home equipment in your own home might activate however might fail to operate in a correct approach, and this might trigger critical inconvenience in addition to enhance your vitality payments. As such, you need to carefully monitor your equipment and search for indicators which will affirm it isn’t working to the perfect of their means. As an illustration, if it takes twice as lengthy to cook dinner your favourite recipes, then you definitely instantly want oven restore. For those who let all these points go unattended for even few weeks, it may price you a whole bunch of when it’s possible you’ll find yourself spending extra on shopping for a brand-new equipment, or paying large vitality payments. The most effective plan of action is to discover a skilled equipment restore knowledgeable and take care of the issue instantly.

Elevated Vitality Payments

One main signal that you just want fast equipment restore can truly be present in your month-to-month vitality payments. Whilst you might not have seen it takes longer to your dryer to dry your garments, however you’ll undoubtedly discover a sudden enhance in your month-to-month electrical energy payments if its cycles are taking longer. Whenever you begin noticing that your cycles are taking longer, it’s undoubtedly a good suggestion to go searching in your own home to see in case your home equipment are working to the perfect of their means. In case your air conditioner is working too arduous, then it may also enhance your vitality payments. On this state of affairs, you need to contemplate air conditioner restore. For those who fail to take the initiative to rent a good equipment restore service instantly to safe knowledgeable AC restore, then you would stand to lose some huge cash in the long term.

Get Skilled Assist Proper Away

The best approach to make sure your funds are protected is to get environment friendly equipment restore service as quickly as you’ll be able to. Whilst you might imagine it can save you some cash by laying aside over or fridge restore, the reality is that ready might normally price you extra. Equipment points can go from dangerous to worse inside no time, so it’s best if you happen to don’t take any possibilities. You possibly can both carry out equipment restore by yourself, or contact an expert equipment restore service that can assist you get your malfunctioning home equipment operating in good situation as soon as extra.

So if you happen to’ve determined to get your home equipment repaired professionally, you should definitely select your organization rigorously. If in case you have guarantee in your equipment, it’s higher to make use of a selected firm as it’s possible you’ll not need to void your guarantee. If you wish to select your personal equipment restore technician, store round. Repute can inform a lot. In lots of circumstances, you’ll be able to search references out of your coworkers, household and associates. You might need to make sure that your equipment restore is finished the precise approach the primary time and with as little price as attainable. Nevertheless, understand that most cost-effective isn’t all the time the perfect. Low price is fascinating, however trustworthiness and reliability are essential too.

For Most Financial savings, Think about Equipment Restore As an Various to Substitute

Home equipment like washers, stoves, fridges, and rubbish disposals are troublesome to reside with when they’re damaged and dear to exchange. Nonetheless, with assist out of your native equipment restore store it can save you your self the trouble of dwelling with a malfunctioning equipment in addition to the expense of getting a brand new one.

In-home home equipment are great to have and supply ease and luxury as they permit us to keep away from quite a lot of exhausting work. Nonetheless, as our home equipment combine extra and newer digital expertise, home equipment have much more components to interrupt than ever earlier than. Whether or not it’s a management panel on a excessive tech dryer or the ice maker in your fridge door, it’s probably simpler to interrupt and tougher to repair than it was in years previous. That is the place an equipment restore store can are available in fairly helpful kenmore appliance repair altadena.

With the assistance of the professionals, you may have home equipment repaired in each a part of your private home, together with:

Rubbish disposals
All of those home equipment and extra could be repaired by an equipment restore store, leaving your life hassle-free and your price range in management.

Issues like oven restore and washer and dryer restore are particularly troublesome to do as these home equipment are composed of so many various components. New energy-efficient washers are in fixed want of restore as they could start to scent and may want a gasket changed virtually yearly. Ovens, however, have electrical components that take time and information to repair. But, these points could be simply and safely amended by a restore group that understands home equipment and learn how to repair them, permitting you to take management of your private home as soon as once more.

Everyone knows how simple home equipment could make life, and all of us perceive how depressing we could be with out them. Due to this fact, you will need to discover a dependable main equipment restore knowledgeable who could make life with home equipment as fulfilling appropriately. Do not spend time and power worrying about damaged home equipment or attempting to repair them your self: Name in knowledgeable and get the job finished proper.

In the event you’re able to get your family home equipment again on monitor, do not accept buying a model new mannequin when you may get an reasonably priced equipment restore out of your native consultants. Your nearest specialists will make fixing your home equipment a complete cinch, so do not put it off. Act now!

How to Repair the Refrigerator Door Seal

The majority of refrigerator doors already possess a rubber seal on the inside of the fridge unit. The rubber seal is sometimes referred to as a refrigerator gasket that is used in order to maintain the cool temperature of the inside of fridges. This serves to protect the food. Seals are also commonly used in freezer units as well.

After the refrigerator has been opened and closed numerous times, the seal will inevitably become worn and create gaps that can lead to leakage of cool air.

This can cause the food to become spoiled and even waste you money on electrical bills. If the seals become cracked, it can also shorten the lifespan of the refrigerator. However, using the correct equipment, parts, and tools, you will be able to repair the seal on the refrigerator and save your fridge as well as save energy immediately Jennair Appliance Repair Los Angeles.

In order to repair a cracked or damaged refrigerator seal, there are few materials that are needed. These include weather stripping tape, a new refrigerator seal, and a screwdriver.

Once you have all of the materials that you require, the following steps can be used in order to make your fridge as good as new:

Step #1
The first step is to buy the appropriate refrigerator seal for the door. Check the label of the refrigerator that is present within the fridge. It will tell you the measurements and dimensions that are required and may even provide you with a product model number. On the off chance that there is no label within the fridge, measure the seal of the door yourself. Make sure that you replace the seal using the correct dimensions. You can likely buy a replacement seal from any store that sells appliances.

Step #2
Locate the retainer that is attached to the perimeter of the door. Lift the inside edge of the seal and loosen the screws that are used to lock the retainer of the fridge. The seal should slip from beneath the retainer of the fridge. However, make sure that you do not apply excessive force.

Step #3
Slip the seal of the door from behind the liner. Begin to situate the new door seal into the top of the refrigerator. Ensure that you fit the seal around the entirety of the fridge. After the seal is completely in place, make sure that the door can open and close. This will ensure that the seal is properly aligned. Make sure that the screws are thoroughly retightened.

Step #4
Check the door for gaps and twists in the seal. The weather tape should then be used to close any gaps. You can even use a blow dryer in order to shape the seal as well.

Home Appliances – Source For Great Comfort

Share this article on Pinterest
Home Appliances:

Life without home appliances is simply incomplete; one cannot do much without assistance and, today everyone wants to complete their chores in a very short time. Home appliances not only help us accomplish home tasks in minimum time but also lessen our work burden. From cooking to washing clothes and dishes appliances have dominated every aspect of our lives in a very positive way Appliance Repair Van Nuys.


Buying home appliances is very common because you can find them anywhere in your city; that are available almost everywhere and, today every country is manufacturing these appliances on a very large scale. Home appliances are manufactured by many large industries and are available in various brands; you see them around you all the time. The logos and brand names are often engraved or printed on these useful gadgets; most of the appliances’ qualities are commonly judged by manufacturer’s name. As with the quality output by these appliances; their shapes, colors and control systems also matter a lot – the more attractive these look, the more increases in the sales company experiences. From offices to studio apartments and even caravans; these appliances are indeed a basic necessity for everyone. Some of the most commonly used home appliances include refrigerators, washers, mixers, coffee makers, food processors, dryers, dishwashers and many more. In early days, home appliances tended to be a bit noisy and used more electric power. Today with new techniques, they operate without sound and do not consume much power. These days even wireless appliances are taking lead and one can carry these reliable appliances anywhere.

Quality and Service:

When it comes to buying appliances; you would definitely get confused as there is a plethora of them in the market. Make sure you be smart when buying a home appliance; the quality and the manufacturer’s brand really matter. For satisfaction and convenience doing research on appliances would be helpful. Make sure the home appliance you aim to buy fit in your budget; for further details also visit a service centre. Almost every reliable brand or company has its service center in most cities; you can visit one nearest you to get information regarding latest offerings.

Taking Care:

Appliances might be a luxury, you might want to use them on daily basis, but keep in mind they do break down due to frequent use. Service centers and home appliance repairs offer you great help; they also include heat repair. You may face problems with appliances as they get old or if over-used; these problems may be with the operation, system controls, motors and a such like. In such a case consulting technicians of the company would be a good idea. For example; sometimes your refrigerator’s cooling capacity gets low, ice builds up in freezer compartment, the drain flow blocks and the fan runs on continually making noise, or refrigerator stops making ice because refrigerator is not cooling the water enough, the ice dispenser stops working, refrigerator does not dispense water or ice in spite of pressing buttons; for these cases you’d find many refrigerator repair servicein your area.

Chicago Refrigerator Repair offers best repairing services, and has qualified technicians. Since home appliances are machines and one totally depends on their capabilities and performance; it’s choosing right appliance and proper quality matters a great deal. These appliances work with electricity, and overloading them causes malfunction nd severe damage. Make sure that you invest your hard earned money on a right thing and consult the company’s official technicians.

Precautions on Repairing Major Appliances

Appliances used in daily life can be said one of the most important need in our life as they help provide comfort and also make our life easier at the same time. However, when something happens, such as a breakdown or also malfunction, most individuals do not know what to do next and eventually spoil the appliances while trying to tinker in the purpose to make it work. Taking that into view, below are some methods on repairing major appliances made easy that can be tried or practiced by almost anyone.

Appliance repair has a lot to do with the power supplied to a particular appliance Whirlpool Appliance Repair Los Angeles. Taking that into view, one should always make sure that adequate or suitable power is supplied to their appliances as unsuitable amounts would not only cause problem but might even spoil a device. Hence, if your power plug has problems such as leakage or a blown fuse take time and be precise in placing the wires at the correct ends or outlets. Adapter plugs are also a good way to go when a power supply is not suitable as it will control the voltage to a suitable amount needed.

When you’re planning an appliance repair always make sure that you have the proper equipment with you. Do not try to use any tool you find as you may eventually cause a screw or nut to lose its grip that will eventually lead to bigger problems. Furthermore, if the parts are held together using rivets or welds; do not attend to the problem on your own. Instead call a professional as rivets and welds are not easy to dismantle and even harder to fix the parts back together again.

Magic Chef Repairs

Magic chef repairs are becoming more and more difficult, not because they’re difficult machines to repair, but because the spare parts they need are running out – and fast.

What a lot of owners of Magic Chef products don’t know is that the company stopped production of some of their more complex appliances several years ago. This means that they no longer make ovens, washing machines or tumble dryers Whirlpool Appliance Repair Los Angeles.

This is terrible news for the horde of people who own these appliances and need them to be repaired. The number of replacement parts is going nowhere but down, and it’s at time when the money is hard to come by for many. This means that you have a situation where there are a number of people with broken down appliances, which although cheap in comparison to the competition were still nevertheless expensive to buy. Combine this with a shortage of spare parts and things seem to be starting to get serious.

The hardest part about Magic Chef repairs isn’t the actual repair work, if you hire an experienced handyman they can get the job done relatively easy. The hardest part is finding where the spare parts you need are, most people tend to quickly search online expecting to find them. Unfortunately for Magic Chef parts is just not the case that they’ll be easily available online. Seeing as production has completely stopped, so had the already limited production of spare parts – all culminating in the fact that finding the parts you need is going to be a very time consuming process. You really have to ask yourself whether it’s even worth it, because you may only be lengthening its life by just a year or so.